Missoula Electric Cooperative recognizes that energy efficiency is the most cost-effective source of new energy, and works to bring energy savings to our agricultural members. By saving energy, farmers may be able to reduce costs, increase irrigation uniformity, decrease the amount of water and fertilizer required and, according to one study, even increase yield.
Missoula Electric is also proud to partner with the Blackfoot Challenge to help make these savings a reality. Below is a list of ag incentive areas we are currently focusing on. For more information on incentive amounts, call MEC at 541-4433.
Click any of the below items to find out more about our programs.
|Replace worn nozzle with new flow-controlling type nozzle for impact sprinklers||$4.00/nozzlei|
|Replace leaking impact sprinkler with rebuilt or new impact sprinkler||$3.75/sprinkleri|
|New nozzle for impact sprinkler replacing existing worn nozzle of same flow rate or less||$1.50/nozzlei|
|New nozzle for center pivot and lateral moves||$1.00/nozzle|
|New rotating type sprinklers that replace impact sprinklers||$4.00/sprinkleri|
|Replace leaking pipe section and riser cap gaskets for wheel or hand lines or portable main line gasket with new gasket||$2.75/gasket|
|New low-pressure regulators||$5.00/regulatori|
|New rotating type sprinklers that replace low-pressure||$4.00/sprinkleri|
|New multiple configuration nozzles for low-pressure pivotii sprinklers||$3.00/sprinkleri|
|New multi-trajectory sprays that replace impact sprinklers||$4.00/sprinkleri|
|New multi-trajectory sprays that replace low-pressure sprinklers||$1.00/sprinkleri|
|Replace leaking drain gaskets with new gaskets on wheel-lines, hand lines or pivotsii||$1.00/drain|
|New hubs for wheel-lines||$14.50/hub|
|New goose-neck elbow for new drop tubes (to convert existing sprinkler equipment mounted on top of the pivotii to low-pressure sprinkler package)||$1.65/goose-neck|
|New drop tube for low-pressure pivotii sprinklers (minimum three feet length)||$3.00/drop tube|
|Replace leaking center pivot base boot gasket with new gasket||$175.00/pivot|
|Pipe repair of leaking hand lines, wheel lines and portable mainline||$10.00/pipe section|
|Rebuild or replace leaking or malfunctioning leveler with new or rebuilt wheel-line leveler||$0.75/leveler|
Custom projects exist for irrigation pumps which are electrically powered and 20 hp or greater in size. Custom Projects must be approved by MEC prior to purchasing or installing any equipment. In addition, irrigators must obtain a pump test/system evaluation from a qualified technical service provider approved by MEC.
Irrigation Pump Testing and System Analysis
The best way to establish a baseline for your system’s efficiency is through an irrigation/pump test or a full system analysis. The purpose of pump testing is to identify ways to improve irrigation system efficiency and performance.
The irrigation pump must be electrically powered, 20 hp or greater and must not have been tested through BPA-sponsored pump testing services within the past five years.
The irrigation pump must have been in operation for the two previous years.
The irrigation pump test must be performed by an individual possessing pump testing knowledge and experience.
Customers and qualified vendors must use the BPA Screening Tool in EE Central to limit the amount of dry holes (i.e., pump tests that do not result in a BPA-approved custom project).
This measure applies to pumping operations that deliver, distribute or transport irrigation water with qualifying VFDs from 20 to 500 hp. Eligible installations are limited to turbine pumps with substantial variation in flowrates (20% variation or more) or discharge pressure requirements (10% variation or more). BPA recommends that all new VFD installations meet the IEEE 519 standard. Rebates for qualifying installations are up to $60 per horsepower.
Members need to contact MEC prior to scheduling any testing or performing any irrigation system upgrades to avoid negating any potential rebates.